The Hallmark of Geneva is not an end in itself—it is a standard along the path to the highest possible innovation and excellence.
Bana göre Roger Dubuis yeni Easy Diver da üstüne koyarak gitmiş!Hatta ROGER DUBUIS çıldırmış

KASA ve KADRAN :
Eski ve yeni Easy Diver arasında kasa aynı çap olsada 46mm aralarında büyük farklılıklar var!!
Eski Easy diver'ı ilk gördüğümde vaaaaaaay demiştim ama şimdi yeniyle eskiyi karşılaştırdığımda
aslında eski Easy Diver'ın ne kadar gözümü yorduğunu farkettim...
her iki modeldede saat 6'da saniye bulunmakda ama yeni modelde daha kibar sadece rakamlardan oluşuyor
eski modelde rakamlar ve indekslerden gözü yoran bi görüntüsü vardı!
Yeni modelde sadece rakamla 12 belirtilmiş geri kalan sadece indekslerden oluşuyo ve artı olarak saat 6'da bulunan saniyenin altına GENEVE yazısı eklenmiş ki bu daha hoş bi hava vermiş saat'e...
sanki saatin içindeki kalabalık kalkmış daha modern bi hava almış! akrep ve yelkovan kılıcı andıran bi keskinlikle bitiyor ve bu da saate daha fazla agresiflik katmış! Ve bi ROGER DUBUIS klasiği saatin belli kısımlarında tekrar carbon fiber malzeme kullanılmış az ve öz olduğu için benim hoşuma gidiyor...









MEKANİZMA :
Yeni easy diverda mekanizma olarak RD 821 isimli mekanizma kullanılmış
RD821 168 parçadan oluşan 3.43mm kalınlığında 33 jewels 48 saat power rezerve sahip bi mekanizma önceki Easy diver da RD14 isimli rotoru sarı renkte olana mekanizma kullanılırken bu modelde çelik üstüne haklı olarak manufacture (herşey tek bi fabrikada üretildiği için) Roger DUBUIS yazıyor!! ve ayrıca COSC sahibi bir mekanizma

KAYIŞ :
Saatin kauçuk kayışı hemen ortasında RD harfleriyle süslenmiş bileği rahatça saran tek katlamalı tokayla açılan ve kapanan bi mekanizmaya sahip!
ve Roger Dubuis Every Movement Stamped with the Hallmark of Geneva diye bahsetmiş sitesinde!
benim zavallı incelememden ziyade herkesin Roger DUBUis'ın sitesinde ki şu bölümü okuyup değerlendirmesini istedim ve açıklama şöyle ki bence bu bile yeter bu saati almaya!!
Every Movement Stamped with the Hallmark of Geneva
From the manufacture’s beginning, Roger Dubuis made the radical decision to ensure that every one of its movements, without exception, is certified by the Hallmark of Geneva. This mandate sets a marvelously high standard of excellence in the Dubuis manufacture process, and the difficulty of fulfilling the Hallmark’s requirements only fuels the fires of Roger Dubuis’ ingenious design. For the Dubuis manufacture, the Hallmark of Geneva is not an end in itself—it is a standard along the path to the highest possible innovation and excellence.
To qualify for the Hallmark of Geneva, a mechanical movement must be assembled and adjusted within the Canton of Geneva, numbered, and in adherence to the finest practices of watchmaking. It also must comply with the 12 criteria as defined by Geneva’s Technical Commission:
1. All steel parts must have polished edges and drawn flanks, and all visible surfaces must be smoothed.
2. The gear-train and the escapement must have ruby jewels in polished holes. Jewels on the bridge side must be olive-drilled and their sinks polished.
3. The pivot shanks and pinion leaves must be polished.
4. Gear-train wheels must be chamfered on their top and bottom sides and their sinks must be polished. For wheels 0.15 mm thick or less, bevelling is tolerated on the bridge side only.
5. The ratchet and transmission wheel must be finished according to registered models.
6. The balance spring must be secured by a sliding stud cap with a round head and neck. Mobile stud holders are accepted.
7. Fitted or slit indexes are accepted with a fastening system.
8. The escape wheel must be light. Its thickness must not exceed 0.16 mm for large components and 0.13 mm for components under 18 mm. Locking faces must be polished.
9. The angle traversed by the pallet lever must be contained within two solid bankings. Pins or studs are not permitted.
10. Wire springs are not permitted.
11. Regulating systems having a balance wheel with variable radius of rotation are permitted on condition they comply with point one above.
12. Movements with shock absorbers are permitted.
The Hallmark of Geneva is a clear, recognizable symbol that connoisseurs and experts can implicitly trust: a guarantee of quality and excellence. And, impressively, Roger Dubuis is the only manufacture to fulfill all of these requirements with every single part in every single movement it produces.
Not : Herhangi bi yanlışım veya eksiğim varsa tamamlarsanız sevinirim Üstadlar!!









